Vue d'ensemble
The VIOX VRL7E is an electronic Type AC residual current circuit breaker with overcurrent protection for AC 230 V, 50/60 Hz final distribution circuits. Its 1P+N configuration combines residual-current, overload and short-circuit protection in one compact device. The Type AC detection system responds to sinusoidal alternating residual currents, while B and C thermomagnetic tripping characteristics support different circuit and load requirements. The RCBO is intended for residential, commercial and light industrial distribution boards and installs on a standard 35 mm DIN rail.
Caractéristiques
- Electronic Type AC residual-current detection.
- Residual-current, overload and short-circuit protection.
- 1P+N configuration for AC 230 V circuits.
- B and C thermomagnetic release characteristics.
- 4.5 kA rated short-circuit capacity.
- Indicateur de courant de défaut intégré.
- 35 mm DIN-rail mounting with a fast-clip device.
Spécifications
Données électriques
| Paramètre | Spécification |
|---|---|
| Operating Mode | Electronic type |
| Courant Nominal | 2, 4, 6, 10, 16, 20, 25, 32, 40 A |
| Configuration des pôles | 1P+N |
| Tension opérationnelle nominale | 230 V AC |
| Fréquence nominale | 50/60 Hz |
| Tension d'isolation nominale | 250 V |
| Tension nominale de tenue aux impulsions | 4 kV, 1,2/50 μs |
| Tension d'essai diélectrique | 2 kV pendant 1 minute |
Données de protection
| Paramètre | Spécification |
|---|---|
| Type de courant résiduel | Type AC |
| Thermomagnetic Release Characteristic | B, C |
| Courant différentiel assigné | 10, 30, 100 mA |
| Pouvoir de coupure et de fermeture résiduel assigné | 500 A |
| Rated Short-Circuit Capacity | 4,5 kA |
| Break Time at IΔn | ≤ 0.1 s |
| Degré de pollution | 2 |
Données mécaniques et d'installation
| Paramètre | Spécification |
|---|---|
| Durée de vie électrique | 4 000 manœuvres |
| Durée de vie mécanique | 10 000 opérations |
| Fault-Current Indicator | Oui |
| Degré de protection | IP20 |
| Terminal Connection | Cable / pin-type busbar / U-type busbar |
| Cable Terminal Capacity | 25 mm², AWG 18-5, top/bottom |
| Busbar Terminal Capacity | 25 mm², AWG 18-3, top/bottom |
| Montage | 35 mm DIN rail to EN 60715; fast-clip device |
| Supply Connection | From top |
Environmental Data
| Paramètre | Spécification |
|---|---|
| Température ambiante | -5 °C to +40 °C; daily average ≤ 35 °C |
| Température de stockage | -25 °C to +70 °C |
Standard
| Paramètre | Spécification |
|---|---|
| Standard | CEI/EN 61009-1 |
Guide de sélection
| Élément de code | Signification | Valeurs disponibles |
|---|---|---|
| V | Identification d'entreprise VIOX | V |
| RL | Famille de produits RCBO | RL |
| 7E | Série de conception | 7E |
| Courbe | Courbe de déclenchement surintensité | B ou C |
| Actuel | Courant nominal | 2-40 A |
| Sensibilité | Courant différentiel résiduel assigné | 10, 30 or 100 mA |
| Pôles | Ordering designation | 2P in the catalog example |
| Example Model | Configuration |
|---|---|
| VRL7E-B16-10 | B curve, 16 A, 10 mA |
| VRL7E-C20-30 | C curve, 20 A, 30 mA |
| VRL7E-C40-100 | C curve, 40 A, 100 mA |
Courbe de déclenchement
Select a B or C thermomagnetic release characteristic according to the circuit and load requirements.
Courant Nominal
Select one of the listed ratings from 2 A to 40 A.
Sensibilité résiduelle
Select a rated residual operating current of 10, 30 or 100 mA.
Configuration du circuit
The technical specification identifies a 1P+N configuration for AC 230 V final distribution circuits.
Courbes de déplacement
The VRL7E is available with B and C time-current tripping characteristics. The catalog provides time-current graphs for both curves and specifies a residual-current break time of no more than 0.1 seconds at IΔn.
| Protection Characteristic | Available Option |
|---|---|
| Thermomagnetic Release | B or C curve |
| Residual-Current Break Time | ≤ 0.1 s at IΔn |
Dimensions
Applications
- Residential final distribution boards.
- Commercial final distribution circuits.
- Light industrial distribution boards.
- AC 230 V circuits requiring combined Type AC residual-current and overcurrent protection.
Installation
- Install on a 35 mm DIN rail conforming to EN 60715 using the fast-clip device.
- Connect the supply from the top.
- Use cable, pin-type busbar or U-type busbar connections as specified.
- Observe the stated 25 mm² terminal capacity for cable and busbar connections.
- Install within the specified ambient temperature range of -5 °C to +40 °C.
Téléchargements
FAQ
What residual-current type does the VRL7E use?
It uses electronic Type AC detection for sinusoidal alternating residual currents.
Quels sont les courants nominaux In disponibles ?
The available ratings are 2, 4, 6, 10, 16, 20, 25, 32 and 40 A.
Which residual-current sensitivities are available?
The available rated residual operating currents are 10, 30 and 100 mA.
What is the VRL7E short-circuit capacity?
The rated short-circuit capacity is 4.5 kA.
How is the VRL7E installed?
It mounts on a 35 mm DIN rail conforming to EN 60715 and uses a fast-clip device. The supply connection is from the top.
