RCCB Manufacturer & OEM Supplier
Disjuntores de Corrente Residual (RCCB)
Compare VIOX RCCB series for conventional AC, pulsating DC, mixed-frequency, smooth-DC and EV charging applications. Published models cover 16–100A ratings in 2P and 4P configurations.
- Type AC, A, ASi, F, B, B+ and EV variants
- Model-specific datasheets and documentation review
- OEM marking, packaging and wholesale supply
Choose by residual-current type
Which RCCB series should you start with?
Begin with the residual-current waveform and application, then confirm rated current, IΔn, poles, voltage and upstream overcurrent protection.
VKL11
Start here for conventional AC or pulsating-DC residual-current protection in residential, commercial and distribution applications.
- Tipo
- Type AC / A / ASi
- Corrente nominal
- 16–100A
- Pólos
- 2P / 4P
VKL11F
For circuits with single-phase electronic equipment and mixed-frequency residual currents up to the model’s declared operating range.
- Tipo
- Tipo F
- Corrente nominal
- 16–100A
- Pólos
- 2P / 4P
VKL11B
For installations where smooth DC and higher-frequency residual currents must be detected, subject to the exact system and model requirements.
- Tipo
- Tipo B / B+
- Corrente nominal
- 16–100A
- Pólos
- 2P / 4P
VKL11-EV
For Mode 3 EV charging, with Type A or Type F residual-current protection and integrated smooth-DC detection that switches off at a maximum 6mA threshold for the declared variants.
- Tipo
- Type A EV / F EV
- Corrente nominal
- 16–100A
- Pólos
- 2P / 4P
Interactive specification builder
VIOX RCCB Selector
Describe the supply system, connected load and protection objective. The selector builds a preliminary RCCB specification, identifies a candidate VIOX series and lists every item that still needs verification.
Selection status
Verification RequiredPreliminary RCCB specification
Why this series
Items to confirm
This selector provides a preliminary shortlist, not a final protection design. Equipment-manufacturer instructions, system studies and applicable installation rules take priority.
Model-level comparison
Compare VKL11, VKL11F, VKL11B and VKL11-EV
Use the table to shortlist a series. Verify the exact rating combination and destination-market documents before ordering.
| Série | Tipo de RCCB | Corrente nominal | Corrente residual nominal | Pólos | Tensão nominal | Published standards |
|---|---|---|---|---|---|---|
| VKL11Proteção de uso geral | Type AC / A / ASi | 16–100A | 10mA* / 30mA / 100mA / 300mA | 2P / 4P | 240V / 415V AC | IEC/EN 61008-1 |
| VKL11FMixed-frequency loads | Tipo F | 16–100A | 30mA / 100mA / 300mA | 2P / 4P | 230/240V / 400/415V AC | IEC/EN 62423 · IEC/EN 61008-1 |
| VKL11BSmooth DC & high frequency | Tipo B / B+ | 16–100A | B: 30–500mA · B+: 30–300mA | 2P / 4P | 230/240V / 400/415V AC | Type B: IEC/EN 62423 + IEC/EN 61008-1 · Type B+: confirm DIN VDE 0664-400 for the exact variant |
| VKL11-EVMode 3 EV charging | Type A EV / F EV | 16–100A | A-EV: 10–300mA · F-EV: 30mA | 2P / 4P | 240V / 415V AC | A-EV: IEC/EN 61008-1 + IEC 62955 · F-EV: IEC/EN 61008-1 + EN 62423 + OVE E 8601 |
* The 10mA VKL11 option applies to published 16–40A configurations. IEC 62423 covers Type F and Type B; a Type B+ claim must be confirmed against the exact variant and applicable DIN VDE 0664-400 evidence. The VKL11-EV catalog lists IEC 62955 for VKL11A-EV, while VKL11F-EV is listed with EN 62423 and OVE E 8601. Confirm the ordered variant and supporting documents.
Guia de aplicação
Match the RCCB series to the load profile.
Start with the connected equipment and expected residual-current waveform. Then verify the required type, sensitivity, poles, voltage and overcurrent coordination.
Distribuição Geral
Residential, commercial and panel-distribution circuits requiring the appropriate Type AC, A or ASi variant.
View VKL11
Electronic & Variable-Frequency Loads
Single-phase drives, heat pumps, HVAC and electronic equipment that may produce mixed-frequency residual currents.
View VKL11F
Power Conversion Systems
PV, battery storage, UPS and drive applications where the system requires smooth-DC residual-current detection.
View VKL11B
Mode 3 EV Charging
Residential and commercial Mode 3 charging points requiring a declared A-EV or F-EV configuration.
View VKL11-EVBefore placing an order
Turn the circuit requirement into a checkable RCCB specification.
An RCCB should not be chosen from one headline rating. Record the complete electrical requirement and match it to the exact published model.
Open the complete RCCB selection guide- 01
Confirm system voltage and conductors
Define the single-phase or three-phase circuit, neutral arrangement and required 2P or 4P switching.
- 02
Set rated current and IΔn
State both the continuous-current rating and the required residual operating current.
- 03
Match the residual-current waveform
Use the connected equipment manufacturer’s requirements to select Type AC, A, F, B, B+ or an EV variant.
- 04
Coordinate overcurrent protection
Confirm the MCB, fuse or other overcurrent device because an RCCB does not provide overload or short-circuit protection.
- 05
Verify the exact document set
Match the model, rating, standard, destination market, certificate request and OEM artwork before production.
Manufacturer & OEM support
Qualify the product and the supply process.
VIOX supports distributors, panel builders and private-label electrical brands with published model data, sample approval and order-specific documentation review.
Fabrico
Review VIOX production and assembly capabilities.
↗02Controlo de qualidade
See how incoming, production and finished-product checks are organized.
↗03OEM / ODM
Define marking, packaging, samples and repeat-order references.
↗04Certificações
Request documentation for the exact series, rating and market.
↗Technical resources
One guide for each technical decision.
Use the focused guide for the question at hand, then return here to compare the available VIOX series.
Purchase questions
RCCB sourcing FAQ
Short answers for model selection and document review.
Which VIOX RCCB series should I start with?
Start with VKL11 for Type AC, A or ASi requirements, VKL11F for Type F mixed-frequency loads, VKL11B for Type B or B+ smooth-DC detection, and VKL11-EV for the declared Mode 3 EV charging configurations. Final selection must follow the connected equipment, system design and applicable rules.
Um RCCB fornece proteção contra sobrecarga e curto-circuito?
No. An RCCB provides residual-current protection and must be coordinated with the required MCB, fuse or other overcurrent protective device. Use an RCBO where combined residual-current and overcurrent protection is required in one device.
What information is needed for an RCCB quotation?
Provide the circuit voltage, rated current, pole configuration, RCCB type, rated residual operating current, quantity, destination market, required documents and any OEM marking or packaging requirements.
Are the same certificates and reports available for every RCCB series?
Documentation must be confirmed for the exact model, rating and destination market. Request the applicable datasheet, declaration, certificate or test document before approving a product for a project or private-label program.
Does VKL11-EV include 6mA smooth-DC detection?
The published VKL11-EV catalog states that the A-EV and F-EV variants incorporate smooth-DC residual-current detection and switch off at a maximum 6mA threshold. IEC 62955 is listed for VKL11A-EV, while VKL11F-EV is listed with EN 62423 and OVE E 8601. Confirm the exact variant and supporting documents before specification.
Ready for model review?
Send one complete RCCB requirement.
Include voltage, current, poles, RCCB type, IΔn, quantity, destination market, required documents and OEM details. VIOX will review the closest published series.